Huawei RRU3269 Installation Manual Download Page 16

Page: 16 / 135

RRU3269
Installation Guide

3 Information About the Installation

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Item

Silkscreen

Remarks

CPRI1

Optical/electrical port 1, connected to a
lower-level RRU or the BBU

(3) Indicator

RUN

For details, see 3.3 RRU Indicators.

ALM

ACT

VSWR

CPRI0

CPRI1



The port for transmitting RET signals is determined by the software.



Connect the

CPRI0

port to the BBU by default in the single-mode scenario.

3.3 RRU Indicators

This section describes six indicators on an RRU. They indicate the running status of the RRU.

For detailed positions of RRU indicators, see 3.2 RRU Ports.

Table 3-2 describes RRU indicators.

Table 3-2

RRU Indicators

Indicator

Color

Status

Meaning

RUN

Green

Steady on

The power input is available, but the board
is faulty.

Steady off

No power input is available , or the board is
faulty.

Blinking (on for
1s and off for 1s)

The board is running properly.

Blinking (on for
0.125s and off for
0.125s)

The board software is being loaded , or the
board is not working.

ALM

Red

Steady on

Alarms are generated, and the module must
be replaced.

Blinking (on for
1s and off for 1s)

Alarms are generated. The alarms may be
caused by faults on the related board or
ports. Therefore, you need to locate the
fault before deciding whether to replace the
module.

Summary of Contents for RRU3269








































































































































Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands

Huawei RRU3269, Installation Manual

Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands