Huawei RRU3269 Installation Manual Download Page 3

Page: 3 / 135

RRU3269
Installation Guide

About This Document

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

About This Document

Purpose

This document describes the process of installing DC blade RRU3269 (referred to as RRU in
this document). RRU is short for remote radio unit.

Product Versions

The following table lists the product version related to this document for RRU3269.

Product Name

Solution Version

Product Version

RRU3269



SRAN13.1 and later
versions



eRAN13.1 and later
versions

V100R013C10 and later
versions

Intended Audience

This document is intended for:

Base station installation engineers

Organization

1 Changes in RRU3269 Installation Guide

This section describes the changes in the

RRU3269 Installation Guide

2 Installation Preparations

This chapter describes the reference documents, tools, and instruments that must be ready
before the installation. In addition, it specifies the skills and prerequisites that installation
engineers must have.

3 Information About the Installation

Before installing an RRU, you must be familiar with its exterior, ports, indicators, installation
scenarios, and installation clearance requirements.

Summary of Contents for RRU3269








































































































































Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands

Huawei RRU3269, Installation Manual

Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands