Huawei RRU3269 Installation Manual Download Page 21

Page: 21 / 135

RRU3269
Installation Guide

3 Information About the Installation

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential



The diameter of a pole for installing an RRU ranges from 60 mm (2.36 in.) to 114 mm
(4.49 in.). The recommended diameter is 80 mm (3.15 in.).



The recommended thickness of the pole wall is 3.5 mm (0.14 in.) or above.



When RRUs are installed on a pole, the side-mounted installation is recommended. A
maximum of three RRUs can be installed on a pole with the diameter ranging from 60 mm
(2.36 in.) to 76 mm (2.99 in.).



Only a pole whose diameter ranges from 76 mm (2.99 in.) to 114 mm (4.49 in.) supports
more than three RRUs.

Figure 3-7 shows a single RRU installed on a pole.

Figure 3-7

A single RRU installed on a pole

Figure 3-8 shows two RRUs installed on a pole.

Summary of Contents for RRU3269








































































































































Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands

Huawei RRU3269, Installation Manual

Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands