Huawei RRU3269 Installation Manual Download Page 10

Page: 10 / 135

RRU3269
Installation Guide

2 Installation Preparations

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Installation Preparations

About This Chapter

This chapter describes the reference documents, tools, and instruments that must be ready
before the installation. In addition, it specifies the skills and prerequisites that installation
engineers must have.

2.1 Reference Documents

Before the installation, you must be familiar with reference documents.

2.2 Tools and Instruments

This section describes the tools and instruments that must be prepared before the remote radio
unit (RRU) installation.

2.3 Skills and Requirements for Onsite Personnel

Onsite personnel must be qualified and trained. Before performing any operation, onsite
personnel must be familiar with correct operation methods and safety precautions.

2.1 Reference Documents

Before the installation, you must be familiar with reference documents.

The following reference documents are required during RRU installation:



Safety Information



RRU3269 Hardware Description



DBS3900 Installation Guide

DBS5900 Installation Guide

For details about RRU auxiliary devices, see "RRU Auxiliary Devices" in the corresponding RRU
hardware description.

2.2 Tools and Instruments

This section describes the tools and instruments that must be prepared before the remote radio
unit (RRU) installation.

Summary of Contents for RRU3269








































































































































Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands

Huawei RRU3269, Installation Manual

Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands