Huawei RRU3269 Installation Manual Download Page 9

Page: 9 / 135

RRU3269
Installation Guide

1 Changes in RRU3269 Installation Guide

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Changes in RRU3269 Installation Guide

This section describes the changes in the

RRU3269 Installation Guide

Draft B (2018-05-15)

This is a draft.

Compared with Draft A (2018-04-14), this issue does not include any new information.

Compared with Draft A (2018-04-14), this issue includes the following change:

Topic

Change Description

12.1 Adding a Female Connector to the
RRU Power Cable on the RRU Side

Optimized the descriptions in this section.

Compared with Draft A (2018-04-14), no information is deleted from this issue.

Draft A (2018-04-14)

This is a draft.

Summary of Contents for RRU3269








































































































































Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands

Huawei RRU3269, Installation Manual

Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands