Huawei LUNA2000-30-S0 User Manual Download Page 107

Page: 107 / 129

System Maintenance

7.1 System Power-Off

Precautions

WARNING

● After the system powers off, the remaining electricity and heat may still cause

electric shocks and body burns. Therefore, wear protective gloves 5 minutes

after the system is powered off before performing any operation on the

battery.You can maintain the battery only when all indicators on the battery are

off.

● When the ESS is running, you can only turn off the DC switch of the battery,

but cannot power off the ESS completely. In this case, you cannot maintain the

battery.

Powering Off the System

Step 1 Turn off the AC switch between the inverter and the power grid.

Step 2 Turn off the DC switch at the bottom of the inverter.

Step 3 Turn off the DC switch between the PV string and the inverter if there is any.

Step 4 Turn off the DC switch on the battery.

----End

7.2 Routine Maintenance

To ensure that the battery can operate properly for a long term, you are advised

to perform routine maintenance on it as described in this chapter.

LUNA2000-(5-30)-S0

User Manual

7 System Maintenance

Issue 07 (2022-01-10)

100

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands