Huawei LUNA2000-30-S0 User Manual Download Page 60

Page: 60 / 129

Type

Tools and Instruments

Hydraulic pliers

Heat-shrink tubing

Heat gun

Personal protective

equipment (PPE)

Safety gloves

Safety goggles

Dust mask

Safety boots

4.3 Determining the Installation Position

Installation Angle Requirement

The battery can be floor-mounted and wall-mounted. The installation angle

requirement is as follows:
●

Do not install the battery at forward tilted, back tilted, side tilted, horizontal,

or upside down positions.

Installation Space Requirements

●

Reserve sufficient clearance around the battery to ensure sufficient space for

installation and heat dissipation.

LUNA2000-(5-30)-S0

User Manual

4 System Installation

Issue 07 (2022-01-10)

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands