Huawei LUNA2000-30-S0 User Manual Download Page 48

Page: 48 / 129

Table 3-8 Mapping relationship

Cascading

Mode

SUN2000

Sdongle

SUN2000-(2KTL-6KTL)-

SUN2000-(2KTL-6KTL)-L1 SUN2000-(2KTL-6KTL)-L1

Sdongle

SUN2000-

(3KTL-10KTL)-M1

SUN2000-(3KTL-10KTL)-

NO TE

The parameters of each battery need to be set separately. When the grid charging function

is enabled, the surplus power generated by one inverter can be used to charge the other

inverter.

WARNING

In the off-grid state, the output phases of cascaded inverters are different. The

load outputs of the Backup Boxes connected to each inverters cannot be

connected in parallel. As shown in the following figure, the P-1 output is

connected to primary O-1 and the P-2 output is connected to O-2. The P-1 and

P-2 load outputs cannot be connected in parallel.

(A) PV string

(B) DC switch

(D) AC switch

(E) ACDU

(F) Smart Power Sensor

(G) Power grid

(H) LUNA2000

(I) 4G Smart Dongle

(J) WLAN-FE Smart

Dongle

(K) Router

(L) FusionSolar

management system

(M) FusionSolar app

(N) Load

(O) Important Load

(P) Backup

(Q) SmartLogger

NO TE

indicates a power cable,

indicates a signal cable,

indicates

wireless communication.

3.2.2 Setting the Grid-tied and Off-grid ESS Mode

The grid-tied and off-grid ESS switches the inverter to the grid connection status

through the Backup Box. When the grid fails, the ESS supplies power to primary

loads in backup mode. When the grid recovers, the ESS automatically switches

back to the grid-tied mode.

LUNA2000-(5-30)-S0

User Manual

3 Application Scenarios and Settings

Issue 07 (2022-01-10)

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands