Huawei LUNA2000-30-S0 User Manual Download Page 49

Page: 49 / 129

●

This mode can be used together with the self-consumption or time-of-use

mode.
–

When the grid is normal, the self-consumption or time-of-use mode is

used.

–

After the grid fails, the ESS switches to the power backup mode. The

battery backup time depends on the battery SOC when the grid fails.

(The battery SOC for power backup can be set based on customer

requirements.)

Enabling Off-grid Mode

On the home screen, choose Settings > Feature parameters and enable Off-grid

mode.

Figure 3-15 Backup power setting

Table 3-9 Grid-tied and off-grid parameter setting

Parameter

Description

Value Range

Off-grid mode

If this parameter is set to Enable, the ESS

switches to the off-grid mode when the grid

fails.

● Enable
● Disable

LUNA2000-(5-30)-S0

User Manual

3 Application Scenarios and Settings

Issue 07 (2022-01-10)

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands