Huawei LUNA2000-30-S0 User Manual Download Page 110

Page: 110 / 129

Alarm

Alarm Name

Alarm

Severity

Possible Cause

Troubleshooting

3002

Battery power control

module

overtemperature

Minor

1. The installation

position of the battery

power control module

is not well ventilated.
2. The ambient

temperature is

excessively high.
3. The battery power

control module is

abnormal.

1. Check the

ventilation and

whether the ambient

temperature of the

[Battery-1/2] power

control module

exceeds the upper

threshold.
2. If the ventilation is

poor or the ambient

temperature is

excessively high,

improve the

ventilation and heat

dissipation.
3. If the ventilation

and ambient

temperature are

normal, contact your

dealer or Huawei

technical support.

3003

Battery power control

module fuse blown

Major

The fuse of the

battery power control

module is blown.

1. Turn off the inverter

AC output switch,

inverter DC input

switch, and battery DC

switch, and wait for 5

minutes.
2. Replace the fuse of

the [Battery-1/2]

power control module.
3. Turn on the battery

DC switch, inverter AC

output switch, and

inverter DC input

switch in sequence. If

the alarm persists,

contact your dealer or

Huawei technical

support.

LUNA2000-(5-30)-S0

User Manual

7 System Maintenance

Issue 07 (2022-01-10)

103

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands