Huawei LUNA2000-30-S0 User Manual Download Page 29

Page: 29 / 129

Application Scenarios and Settings

The LUNA2000 battery is mainly used in grid-tied systems of residential rooftop

PV plants and small-scale PV plants in industrial and commercial scenarios. The

system can be classified into the following three types based on application

scenarios:
●

Grid-tied energy storage system (ESS)

●

Grid-tied and off-grid ESS

●

Off-grid ESS

Multiple working modes can be set, such as maximum self-consumption, time-of-

use, and fully fed to the grid.

3.1 Grid-tied ESS

3.1.1 Grid-tied ESS Networking

Networking 1: Single Inverter

The grid-tied ESS consists of PV strings, LUNA2000 batteries, inverter, AC switch,

loads, power distribution unit (PDU), power meter, and grid.
SUN2000-(2KTL-6KTL)-L1, SUN2000-(3KTL-10KTL)-M1 inverters are supported.
The PV string converts solar energy into electric energy, which is then converted by

the inverter to power loads or be fed to the grid.

LUNA2000-(5-30)-S0

User Manual

3 Application Scenarios and Settings

Issue 07 (2022-01-10)

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands