Huawei LUNA2000-30-S0 User Manual Download Page 91

Page: 91 / 129

Figure 6-3 FusionSolar App Quick Guide

6.3.1 Battery Deployment

NO TE

● During system deployment, if the communications cables /Enable– are correctly

connected, the SUN2000 enables the battery and the indicator is on. Do not press the

black start button to enable the battery. Otherwise, the communications cable

connection between the SUN2000 and the battery cannot be verified.

● In cascaded networking scenarios, connect an inverter equipped with energy storage

devices for quick deployment.

Function

Add a battery and set the working mode on the quick settings screen of the

inverter.

Scenario 1: Quick Settings for Single Inverter or Cascaded System Based on

Smart Dongle Networking

Step 1 Log in to the FusionSolar app as installer, tap Setup Wizard, and scan the inverter

QR code (when the Smart Dongle is connected, scan the QR code of the inverter

connected to the Smart Dongle).

LUNA2000-(5-30)-S0

User Manual

6 System Commissioning

Issue 07 (2022-01-10)

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands