Huawei LUNA2000-30-S0 User Manual Download Page 58

Page: 58 / 129

System Installation

4.1 Checking Before the Installation

Checking the Outer Packing

Before unpacking the battery, check the outer packing for damage, such as holes

and cracks, and check the battery model. If any damage is found or the battery

model is not what you requested, do not unpack the product and contact your

dealer as soon as possible.

Checking Deliverables

After unpacking the battery, check that the deliverables are intact and complete,

and free from any obvious damage. If any item is missing or damaged, contact

your dealer.

NO TE

For details about the number of deliverables delivered with the battery, see the

Packing List

in the packing case.

4.2 Preparing Tools and Instruments

Type

Tools and Instruments

Installation

Hammer drill (with a

drill bit of 8 mm)

Torque socket wrench

Torque wrench

LUNA2000-(5-30)-S0

User Manual

4 System Installation

Issue 07 (2022-01-10)

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands