Huawei LUNA2000-30-S0 User Manual Download Page 90

Page: 90 / 129

Category

Status (Blinking at Long

Intervals: On for 1s and then

Off for 1s; Blinking at Short

Intervals: On for 0.2s and

then Off for 0.2s)

Description

Green

Battery level. Each bar indicates 10%.

Steady red

The first three bars indicate the number

of faulty battery expansion modules.

6.3 Battery Commissioning

Download and install the FusionSolar app

●

Method 1: Access https://solar.huawei.com using the mobile phone browser

and download the latest installation package.

Figure 6-1 Download Mode

●

Method 2: Search for FusionSolar on Huawei AppGallery and download the

latest installation package.

●

Method 3: Scan the following QR code and download the latest installation

package.

Figure 6-2 QR code

Download and install the latest FusionSolar app by referring to the quick guide for

the corresponding inverter model or the

FusionSolar App Quick Guide

. Then

has been created). You can obtain the

FusionSolar App Quick Guide

by scanning

the following QR code.

LUNA2000-(5-30)-S0

User Manual

6 System Commissioning

Issue 07 (2022-01-10)

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands