Huawei IPC1601 User Manual Download Page 7

Page: 7 / 92

IPC1601&2602&5602&5603
User Guide

About This Document

Issue 12 (2014-06-12)

Huawei Proprietary and Confidential

5.4 Setting OSD Parameters

Modified description about OSD.

9.5 Resetting the System Service Password

Modified the Reset Service Password page

Chapter 11 Technical Specifications

Modified the technical specifications.

Updates in

Issue 04 (

2013-02-15

)

This issue is the fourth official release, compared to issue 03:

Added

2.1 Product Overview

Added the diagram of SD card slots.

5.2 Setting Video and Audio Stream Parameters

Added description about the recommended bit rate.

Modified

3.2 Installing a Lens

Modified the installation procedure of the iris.

9.7 Restoring a Device to Factory Settings

Modified the procedure for restoring to the factory defaults.

Deleted

Chapter 11 Technical Specifications

Deleted the stream range.

Updates in Issue 03 (2012-12-30)

This issue is the third official release, compared to issue 02:

Added

Chapter 1 Security Precautions

Added description about lightening protection measures and working high above the ground.

2.2 Features

Added description about the security features.

6.3.2 Setting Security Authentication

Added description about security authentication.

Modified

9.4 Upgrading Devices

Modified description about device upgrade.

Summary of Contents for IPC1601





























































































Search results

Summary of Contents for IPC1601

Reviews:

Related manuals for IPC1601

Brands by name

Popular brands

Huawei IPC1601, User Manual

Search results

Summary of Contents for IPC1601

Reviews:

Related manuals for IPC1601

Brands by name

Popular brands