VARI FOCAL COLOUR DOME CAMERA
USER MANUAL
FEATURES
●
1/3" Sony CCD
.
●
Automatic back-light compensation improves the image quality.
●
Auto-IRIS controlled by electronic system.
●
Automatic White Balance function and Automatic Gain Control function.
●
Manual pan /tilt mechanism,
.
●
The camera use high sensitive colour interline transfer
3-Axis Rotation
Accept 12VDC power supply
.
Ⅰ
Ⅱ
The installation should be made by qualified service personnel or system
installers and should confirm to all local codes.
Safety Precautions
1. Power supply
(1) Use with a 12VDCregulated power supply .
(2) To prevent fire or electrical shock, UL listed class 2 wiring should be used
for the 12VDC input terminal.
(3) Be used to connect each lead to the appropriate terminal. Wrong connection
may cause malfunction and/or damage to the camera.
2.Operating and storage locations
(1).Do not attempt to point the camera at the sun or other extremely bright
objects,no matter the camera is power on or not. It leads to damage of the
CCD(Charge Coupled Device).
(3) . B e s u r e t o u s e a c e i l i n g b o a r d h a v i n g e n o u g h s t r e n g t h t o s u p p o r t
this came ra.
(9). Be sure to use proper screws to mount the camera firmly.
(1) Never attempt to disassemble or modify the camera.
(2) If an abnormality should occur, immediately turn off the power and consult
with expert.
(4).Assemb le the came ra's mai n parts and lens quickly in a clean place.
(5).Do not pull the cable, it may cause disconnection .
Ⅲ
Dome cover (transparent)
Camera body
Dome base
Mounti ng Holes
Parts Description
3
1
(2).When camera is installed next to equipment,such as wireless commu-
nication device,it emits a strong electromagnetic field,some irregularity
such as noise on the monitor screen may happen.
(6).Do not touch the inside of camera even if something is wrong.
(7).Before installation,make sure to disconnect the power supply first,
check the ground connection,and then install it.
(8).Operating temperature range:-10
℃
~+50
℃
,(14
°
F~122
°
F);
Storage temperature range:-20
℃
~+60
℃
, (-4
°
F~140
°
F).
Ⅴ
Ⅵ
Ⅳ
Handling of the unit
2
Body cover
Inner Cover
Mount Bracket
Just using one hand can just gently squeeze the cover using thumb
and index finger the inner cover can just be lifted off, to re attach
just push back, and will click into place.
Tilt locking screw
Using this screw, the slope of the lens can be adjusted
and fixed. normally not needed to adjust.
Cover Notch
This is the guide mark to attach the
cover to the base .
Lid Lock Clip
Used to open or close the
Cover dome. To open the
cover dome, press the locker.
Push it outward and rotate the
main body in UNLOCK direction
when you want to remove the
Mount bracket from the Main
body or to remove the installed
camera from the Mount bracket.
When you
it will click
into place and be re-locked.
reattach
Base release
1.
don’t press too hard.
2. Lift off cover angled as shown, this can be
stiff but this is normal.
Unlock the cover using thumb or screwdriver
Installation Instructions
4
3. Take off inside cover and adjust to suit.
4. Unlock the base using pressing
the plastic clip.Used as a ceiling
or wall fixture. It is fixed using
three long tab screws provided in
the package, allows fixing of pro-
duct to be done cleanly and not
get dust inside camera.
5. Drill a hole in the
place where the
camera is installed
6. Install base first,
and remove ceiling
mount if required.
Ceiling
Ceiling
mount
opener
VAEDR460VFV
ver 1.0
