Huawei IPC1601 User Manual Download Page 72

Page: 72 / 92

IPC1601&2602&5602&5603
User Guide

8 External Device Configuration

Issue 12 (2014-06-12)

Huawei Proprietary and Confidential

Step 2

Set the parameters according to Table 8-2.

Table 8-2

PTZ keyboard parameters

Parameter

Description

Setting

Enable

Select this check box if the device connects
to an external PTZ keyboard.

[Default value]

Deselected

Interface Type

Interface type used by the external PTZ
board.

[Setting method]

Select a value from
the drop-down list
box.

Serial Port

The default value is

COM1

Baud Rate

Baud rate used by the external PTZ
keyboard. The value ranges from 300 bit/s
to 115200 bit/s. The default value is

4800

bit/s..

Data Bits

The value must match the setting used by
the external PTZ keyboard.

Stop Bits

The value must match the setting used by
the external PTZ keyboard.

Parity
Verification

The value must match the setting used by
the external PTZ keyboard.

Step 3

Click

The message "Setting PTZ keyboard Updated" is displayed.

Step 4

Click

The system automatically saves the settings.

----End

Summary of Contents for IPC1601





























































































Search results

Summary of Contents for IPC1601

Reviews:

Related manuals for IPC1601

Brands by name

Popular brands

Huawei IPC1601, User Manual

Search results

Summary of Contents for IPC1601

Reviews:

Related manuals for IPC1601

Brands by name

Popular brands