HTP Hydra Smart RT-199 Service Manual Download

Page: 13 / 48

LP-532 REV. 8.13.2014

Description/Part #

Mixing Valve / 7850P054

Check Point

(Main PCB)

CN 10

Function

This component controls DHW outlet temperature by mixing cold and hot water.

Failure Event

① Water flow is not detected and/or water leakage occurs around the mixing valve.

② Abnormal mixing valve operation.

Effects

① Ignition sequence does not start.

② Operation of product is stopped once water leakage is detected.

Error Code

Er 66

Diagonostic

① Restart the product.

② Check the connection around the mixing valve.

Color / Wire Number

[Mixing Valve]

DHM Y Phase (black) : connector ①

DHM Y Phase (brown) : connector ②

DHM X Phase (red) : connector ③

DHM X Phase (orange) : connector ④

GND (yellow) : connector ⑤

DHM Position sensor (green) : connector ⑥

Flow2 sensor (blue) : connector ⑦

DC 14V (white) : connector ⑧

Description/Part #

APS: Air Pressure Switch /

7850P-047

Check Point

(Main PCB)

CN 11

Function

This component monitors the flue for blockage.

Failure Event

① Combustion noise is generated.

② Imperfect and lifting flame occurs.

③ The unit will not ignite.

Effects

Pressure due to exhaust blockage will affect the water heater operation.

Error Code

Er 29

Diagonostic

① Check APS wiring connection

② Check the hose for blockage or kinking.

③ Check exhaust vent for blockage

④ Check APS resistance using a multi meter.

Color / Wire Number

Air pressure switch (blue) : connector ⑤, ⑬

1. Cold water and hot water mixed
2. Step Control Motor Applied.

3. Operating Fluid : 0℃~80℃ (32 ~ 176℉)
4. Operating Pressure: 0~0.98Mpa

5. Supply Voltage : DC24V
6. PPS material Body
7. DHM : Domestic Hot water Mixing Modulation

① ② ③ ④ ⑤ ⑥ ⑦ ⑧
⑨

⑩

⑪ ⑫ ⑬ ⑭ ⑮

⑯

① ② ③ ④ ⑤ ⑥ ⑦ ⑧

Chapter 2 Components description

CN11

CN10

Summary of Contents for Hydra Smart RT-199

















































Search results

Summary of Contents for Hydra Smart RT-199

Reviews:

Related manuals for Hydra Smart RT-199

Brands by name

Popular brands

HTP Hydra Smart RT-199, Service Manual

Search results

Summary of Contents for Hydra Smart RT-199

Reviews:

Related manuals for Hydra Smart RT-199

Brands by name

Popular brands