background image

89

90

   LP-532 REV. 8.13.2014

LP-532 REV. 8.13.2014

Flushing the Water Heater 

Flushing the Heat Exchanger is a complicated procedure that should only be performed by a qualified service 

technician.

NOTE: 

Improper maintenance WILL AVOID water heater warranty.

1. Disconnect electrical power to the water heater.

2.  Close the shut-off valves on both hot water outlet and cold water inlet lines. (V1 & V2)

3.  Connect one hose “D1” to the valve “V3” and place the free end in the bucket. Connect one of the hoses 

“D3” to the circulation pump outlet and the cold water inlet line at the valve “V4”. Connect other hose “D2” 

to the circulation pump inlet and place the free end in the bucket.

4. Pour the tankless water heater cleaning solution into the bucket. Ensure the cleaning solution is approved       

    for potable water systems.

     Place the drain hose (D1) and the hose (D2) to the pump inlet into the cleaning solution.

5.  Open service valves (V3 & V4) on the hot water outlet and cold water inlet lines.

6.  Turn on the circulation pump. Operate the pump and allow the cleaning solution to circulate through the 

water heater for at least 1 hour at a rate of 4 gallons per minute. This will remove any possible harmful scale 

deposits.

7. Rinse the cleaning solution from the water heater as follows:

    - Remove the free end of the drain hose (D1) from the bucket.

    -  Close service valve, (V4), and open shut-off valve, (V2). Do not open shut-off valve, (V1).

    -  Allow water to flow through the water heater for 5 minutes.

    -  Close shut-off valve (V2).

8. Disconnect all hoses.

9. Remove the cold water inlet filter from water heater and clean out any residues.

10. Reinsert the filter and ensure the filter cap is securely tightened.

11. Connect electrical power to the water heater.

12. Open hot water faucet. Run the water heater continuously for five minutes to ensure all cleaning solution 

is purged from the system. Check for leaks and ensure the water heater is operating properly.

Chapter 6  

Maintenance

Main components diagram and part list

Chapter 7  

Components diagram

 

 

 

   

 

NUMBER 

DESCRIPTION 

PART NUMBER  NUMBER 

DESCRIPTION 

PART NUMBER 

EXHAUST ASSY 

7850P-021 

11 

AIR PRESSURE SWITCH 

7850P-047 

CASE 

7850P-044 

12 

DISPLAY BRACKET 

7850P-065 

DOOR ASSY 

7850P-025 

13 

DISPLAY 

7850P-057 

3-1 

FRONT COVER 

7850P-062 

14 

CONTROL 

7850P-058 

3-2 

DISPLAY PANEL BRACKET 

7850P-024 

15 

CONTROL BRACKET 

7850P-066 

3-3 

DISPLAY PANEL 

7850P-023 

16 

ROCKER SWITCH 

7850P-059 

IGNITION TRANSFORMER 

7850P-045 

17 

FLOW CONTROL VALVE 

7850P-053 

GAS INLET NIPPLE 

7850P-043 

18 

WATER INLET VALVE ASSY 

7850P-018 

OVERHEAT SENSOR 

7850P-050 

18-1 

WATER INLET VALVE BODY 

7850P-067 

DHW SUPPLY PIPE ASSY 

7850P-020 

18-2 

WATER INLET SENSOR 

7850P-015 

7-1 

DHW SUPPLY PIPE 

7850P-063 

18-3 

WATER INLET FILTER 

7850P-017 

7-2 

WATER OUTLET SENSOR 

7850P-019 

18-4 

WATER INLET FILTER CAP 

7850P-016 

N/A 

N/A 

19 

CASE BRACKET (LEFT) 

7850P-068 

SIPHON ASSY 

7850P-014 

20 

CASE BRACKET (RIGHT) 

7850P-069 

10 

SIPHON AIR PRESSURE HOSE 

7850P-064 

21 

INTAKE AIR ASSY 

7850P-022 

 

Summary of Contents for Hydra Smart RT-199

















































Reviews: