HTP Hydra Smart RT-199 Service Manual Download

Page: 37 / 48

LP-532 REV. 8.13.2014

Error code

Meaning

Cause

DHW flow control valve error

(Manual reset)

Not able to supply hot water in

setting temperature when flow rate

exceeds water heater maximum

capacity

Failure event

Flow control valve opearation error.

Check point

① Flow control valve recognizes zero point after turning off

and on the power. Check indication of error after basically

turning off and on the power.

② Check wiring line connection

carefully.

③ If above conditions are normal, replace flow control valve

Chapter 4 Troubleshootion

Error code

Meaning

Cause

Mixing valve error (Manual reset)

Unable to operate normally due to

manual reset error. When flow rate

decreases temperature gap gets

bigger.

Failure event

Mixing valve operation error.

Check point

④ If all things are normal, replace main controller.

① Mixing Valve recognizes zero point after turning off and on the

power. Check indication of error after basically turning off and on the

power.

③ If above conditions are normal, replace mixing valve

② Check wiring line connection

carefully.

Chapter 4 Troubleshootion

WARNING

Failure to turn the power off to the appliance before repair could result in serious injury or death.

WARNING

Failure to turn the power off to the appliance before repair could result in serious injury or death.

Summary of Contents for Hydra Smart RT-199

















































Search results

Summary of Contents for Hydra Smart RT-199

Reviews:

Related manuals for Hydra Smart RT-199

Brands by name

Popular brands

HTP Hydra Smart RT-199, Service Manual

Search results

Summary of Contents for Hydra Smart RT-199

Reviews:

Related manuals for Hydra Smart RT-199

Brands by name

Popular brands