manualshive.com logo in svg

HTP Hydra Smart RT-199, Service Manual

Share
Download
HTP Hydra Smart RT-199 Service Manual Download Page 33

63

64

   LP-532 REV. 8.13.2014

LP-532 REV. 8.13.2014

Error code

Meaning

Cause

Water temperature sensor error 

(Automatic reset)

When heat exchanger’s water 

temperature sensor wiring line is 

disconnected or faulty.

Failure event

  Water temperature sensor (tagget OP) faulty or disconnected.

Check point

① Check if water temperature 

sensor’s wiring connected 

at heat exchanger is 

disconnected. Also check main      

control’s socket.

Water temperature sensor (black/black)

② Connect multimeter leads 

to water temperature sensor’s 

socket and measure the 

resistance value (If value is 0Ω 

it’s a sensor’s malfunction so 

replace it)

Chapter 4  Troubleshootion

Error code

Meaning

Cause

Exhaust Temperature sensor 

error (Automatic reset)

When exhaust temperature sensor 

wiring line is disconnected or 

faulty.

Failure event

 Exhaust temperature sensor faulty or disconnected.

Check point

     

① Check if exhaust temperature 

sensor wiring is disconnected. 

Also check main controllers 

socket.

Exhaust duct (white/blue)

② Connect multimeter leads 

to exhaust temperature sensor 

socket and measure the 

resistance value (If value is 0Ω 

it’s a sensor’s malfunction and will 

need to be replaced )

Chapter 4  Troubleshootion

Summary of Contents for Hydra Smart RT-199

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands