HTP Hydra Smart RT-199 Service Manual Download Page 41

Page: 41 / 48

LP-532 REV. 8.13.2014

Main components Replacement Instructions

3. Flame Detection Sensor

4. Gas Leak Detector
1. Close the gas shut off valve

2. Turn the power off

3. Disconnect all the electrical connection to the

main controller

5. Pluck away PCB’s gas leakage detector.

6. Replace leak detection with new component.

7. Assembly is in the reverse order as the part was

repaired.

8. Open the gas shut off valve

9. Turn the power on

10. Turn the unit on and ensure proper operation.

1. Close the gas shut off valve

2. Turn the power off

3. Disconnect all the electrical connection to the

flame detection sensor

4. Rotate flame detection sensor 45 degrees

clockwise and pull forward.

5. Replace flame detection sensor with new

component.

6. Assembly is in the reverse order as the part was

repaired.

7. Open the gas shut off valve

8. Turn the power on

9. Turn the unit on and ensure proper operation.

NOTE:

Ensure the flame detection sensor is

properly secured.

Chapter 5 Replacement instructions

Main components Replacement Instructions

5. Air pressure swtich (APS)

1. Close the gas shut off valve

2. Turn the power off

3. Disconnect the electrical connection to the APS

4. Separate hose from Air Pressure switch.

5. Loosen Air Pressure switch bracket’s two

screws.

6. Replace APS with new component

7. Assembly is in the reverse order as the part was

repaired.

8. Open the gas shut off valve

9. Turn the power on

10. Turn the unit on and ensure proper operation.

Chapter 5 Replacement instructions

WARNING

Failure to turn the power off to the appliance

before repair could result in serious injury or

Summary of Contents for Hydra Smart RT-199

















































Search results

Summary of Contents for Hydra Smart RT-199

Reviews:

Related manuals for Hydra Smart RT-199

Brands by name

Popular brands

HTP Hydra Smart RT-199, Service Manual

Search results

Summary of Contents for Hydra Smart RT-199

Reviews:

Related manuals for Hydra Smart RT-199

Brands by name

Popular brands