NTI Trinity TX101 Installation And Operation Instructions Manual Download

Page: 1 / 84

Trinity Tx

Model Numbers: Tx

200

Version Date: 2014-08-28

INSTALLATION AND OPERATION
INSTRUCTIONS FOR TRINITY Tx BOILER

TABLE OF CONTENTS

1.0

INTRODUCTION ................................................................................................................ 3

2.0

SPECIFICATIONS .............................................................................................................. 6

3.0

BOILER LOCATION .......................................................................................................... 7

4.0

GENERAL VENTING ....................................................................................................... 10

5.0

VENT/AIR-INLET TERMINATION CLEARANCES ..................................................... 24

6.0

CONDENSATE DRAIN .................................................................................................... 27

7.0

INSTALLING GAS PIPING .............................................................................................. 29

8.0

LIGHTING THE BOILER ................................................................................................. 31

9.0

GAS VALVE AND BURNER SET-UP ............................................................................ 34

10.0

BOILER AND HEATING SYSTEM PIPING ................................................................... 37

11.0

DOMESTIC HOT WATER (DHW) PIPING – TX151C & TX200C (COMBI) ............... 48

12.0

FIELD WIRING ................................................................................................................. 52

13.0

CASCADE INSTRUCTIONS ............................................................................................ 55

14.0

WIRING SCHEMATICS ................................................................................................... 57

15.0

INSTALLATION CHECKLIST ........................................................................................ 59

16.0

ANNUAL MAINTENANCE AND INSPECTION ........................................................... 60

17.0

DISPLAY MENU GUIDE ................................................................................................. 62

18.0

TROUBLESHOOTING ..................................................................................................... 74

19.0

PARTS LIST ...................................................................................................................... 77

HAZARD SYMBOLS AND DEFINITIONS

Danger Sign: Indicates a hazardous situation which, if not avoided, will
result in serious injury or death.

Warning Sign: Indicates a hazardous situation which, if not avoided,
could result in serious injury or death.

Caution Sign plus Safety Alert Symbol: Indicates a hazardous situation
which, if not avoided, could result in minor or moderate injury.

Caution Sign without Safety Alert Symbol: Indicates a hazardous
situation which, if not avoided, could result in property damage.

Notice Sign: Indicates a hazardous situation which, if not avoided,
could result in property damage.

This Boiler must be installed by a licensed and trained Heating
Technician or the

Warranty is Void.

Failure to properly install this

unit may result in property damage, serious injury to occupants, or possibly death.

NTI # 84874

NEW PRODUCT LINE

High Efficiency

Condensing Gas Boiler

Summary of Contents for Trinity TX101





















































































Search results

Summary of Contents for Trinity TX101

Reviews:

Related manuals for Trinity TX101

Brands by name

Popular brands

NTI Trinity TX101, Installation And Operation Instructions Manual

Search results

Summary of Contents for Trinity TX101

Reviews:

Related manuals for Trinity TX101

Brands by name

Popular brands