![background image](http://html.mh-extra.com/html/hp/jetdirect-640n/jetdirect-640n_administrators-manual_163697031.webp)
Default IPv4 behavior
When turned on, a factory-default print server connected to a network through a cable (wired),
retrieves its IPv4 settings by systematically using BOOTP, DHCP, and RARP. This can take several
minutes to complete. If configuration fails, a default IPv4 address is assigned.
Configuration tools that require a specific default IP address on the print server for initial
communication might not function without modification. To view the default IP address settings on the
print server, use the HP Jetdirect configuration page.
TCP/IP configuration tools
When a network connection is established, you can configure an HP Jetdirect print server with valid
TCP/IP parameters for your network, using the following methods:
●
Software solutions
Use installation, setup, and management software running on supported
systems. For more information see
HP software solutions summary on page 7
.
●
BOOTP/TFTP
Download the data from a network-based server by using BOOTP and TFTP
each time the printer is turned on. For more information, see “
Use BOOTP/TFTP (IPv4)
on page 22
”.
The BOOTP daemon (bootpd) must be running on a BOOTP server that is accessible by the
printer.
●
DHCP/TFTP
Use DHCP and TFTP each time the printer is turned on. These protocols are
supported on HP-UX, Solaris, Linux, Microsoft Windows Server 2003, Windows Server 2008,
NetWare, and Mac OS systems. (See your network operating system manuals to verify that your
server supports DHCP.) For more information, see
Use DHCP (IPv4) on page 36
.
NOTE:
For more information about Linux and UNIX systems, see the bootpd
man
page.
On HP-UX systems, a sample DHCP configuration file (dhcptab) might be located in the
/etc
directory.
Because HP-UX does not currently provide dynamic domain name system (DDNS) services for
its DHCP implementations, HP recommends that you set all print server lease durations to
infinite
. This ensures that print server IP addresses remain static until DDNS is provided.
●
RARP
Use RARP to answer the print server's RARP request and supply the print server with the
IP address. The RARP method allows you to only configure the IP address. For more
information, see “
Use RARP (IPv4) on page 37
”.
●
arp and ping commands
(Only for print servers configured with Legacy default IP address
192.0.0.192) Use the
arp
and
ping
commands from your system. For more information, see
“
Use the arp and ping commands (IPv4) on page 38
”.
●
Telnet
Set configuration parameters by creating a Telnet connection from your system to the
HP Jetdirect print server, using the default IP address. Once configured, the print server saves
the configuration when turned off and then turned on. For more information, see “
Use Telnet
(IPv4) on page 39
”.
●
HP Embedded Web Server
Use the HP Embedded Web Server on the HP Jetdirect print server
to set configuration parameters. For more information, see
HP Embedded Web Server (V.
45.xx.nn.xx) on page 63
.
●
Printer control panel
(For printers that support HP Jetdirect control panel menus.) Manually
enter the configuration data, using the printer control panel keys. Because you can configure a
ENWW
IPv4 configuration
21
Summary of Contents for Jetdirect 640n
