![background image](http://html.mh-extra.com/html/hp/jetdirect-640n/jetdirect-640n_administrators-manual_163697055.webp)
Table 3-3
Telnet Commands and Parameters (continued)
psk-passphrase
Passphrase used to generate a network pre-shared key. A passphrase must be from 8
to 63 ASCII characters in the hexadecimal range 21 through 7E (characters 0–9, a–z,
A–Z and numerous special characters including !, @, #, $, %, ^, &, (, ), _, +, =,
−
, {, }, [, ],
\, /, “, <, >, ?, “, ‘, ~).
encryption
Use encryption.
0
(default): Disable.
1
: Enable.
wep-key-method
Format for WEP key entry. WEP key entries must be of the proper length.
ASCII
(default): Use alphanumeric ASCII characters (0–9, a–z, A–Z). For 40/64-bit
encryption, enter 5 characters. For 104/128-bit encryption, enter 13 characters. ASCII
entries are case-sensitive.
HEX
: Use hexadecimal digits (0–9, a–f, A–F). For 40/64-bit encryption, enter10
hexadecimal digits. For 104/128-bit encryption, enter 26 hexadecimal digits. HEX entries
are not case-sensitive.
wep-key
Static WEP encryption key. The print server can store up to four WEP keys using four
key positions (Key 1, 2, 3, 4). To enter a WEP key, specify the key position followed by
the encryption key value, as in the following example:
wep-key 1 0123456789net
In the example, Key 1 is assigned with a with a 128-bit WEP key specified by the value
0123456789net.
You can use the
wep-key-method
command to specify the format of the key value
(hexadecimal digits, or alphanumeric ASCII characters). Alternatively, you can insert an
optional parameter (ASCII or HEX) after the key position, as in the following example:
wep-key 1 ASCII 0123456789net
In the example, Key 1 is assigned a 128-bit WEP key specified by the alphanumeric
ASCII characters 0123456789net.
When assigning static WEP keys, ensure that key positions and key values match other
wireless devices on the network. Ensure that all key values entered are of the same
length, and that WEP key lengths use the proper number of characters or digits.
transmit-key
WEP key position (1, 2, 3, 4) that the print server uses for encrypted communications,
as in the following example:
transmit-key 2
In the example, Key 2 is used for encrypted communications, matching other devices on
the network. The default value is
1
.
dynamic-encrypt
802.1x dynamic encryption. Set to: NONE (default), BASIC, AUTO, WPA, or WPA2.
desired-channel
(Ad hoc only) Specify a desired channel that the print server uses for ad hoc network
association requests. The default is channel 11.
10
: Use channel 10 (2457 MHz).
11
: Use Channel 11 (2462 MHz).
The print server uses this channel to broadcast its availability if it fails to detect and
associate with the specified ad hoc network on any channel.
dot11-switch-time
Specify the time (0 - 120 seconds) for the print server to enable its 802.11 wireless port
when its 10/100TX wired port is disconnected from the network.
ENWW
IPv4 configuration
45
Summary of Contents for Jetdirect 640n
