manualshive.com logo in svg

HP EliteDesk 705 G1, Maintenance And Service Manual

The HP EliteDesk 705 G1 is a powerful and reliable desktop computer designed for business professionals. With its sleek design and top-of-the-line features, this product ensures optimal performance. You can easily access all the necessary information about this device by downloading the free brochure and specs manual from manualshive.com.

Share
Download
background image

Recommended materials and equipment

Materials and equipment that are recommended for use in preventing static electricity include:

●

Antistatic tape

●

Antistatic smocks, aprons, or sleeve protectors

●

Conductive bins and other assembly or soldering aids

●

Conductive foam

●

Conductive tabletop workstations with ground cord of one-/- 10% resistance

●

Static-dissipative table or floor mats with hard tie to ground

●

Field service kits

●

Static awareness labels

●

Wrist straps and footwear straps providing one-/- 10% resistance

●

Material handling packages

●

Conductive plastic bags

●

Conductive plastic tubes

●

Conductive tote boxes

●

Opaque shielding bags

●

Transparent metallized shielding bags

●

Transparent shielding tubes

Operating guidelines

To prevent overheating and to help prolong the life of the computer:

●

Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold.

●

Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides
of the computer and above the monitor to permit the required airflow.

●

Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place the
keyboard, with the keyboard feet down, directly against the front of the desktop unit as this also
restricts airflow.

●

Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other foreign matter
can block the vents and limit the airflow. Be sure to unplug the computer before cleaning the air vents.

●

Never operate the computer with the cover or side panel removed.

●

Do not stack computers on top of each other or place computers so near each other that they are
subject to each other’s re-circulated or preheated air.

●

If the computer is to be operated within a separate enclosure, intake and exhaust ventilation must be
provided on the enclosure, and the same operating guidelines listed above will still apply.

●

Keep liquids away from the computer and keyboard.

30

Chapter 3   Routine care, SATA drive guidelines, and disassembly preparation

Summary of Contents for EliteDesk 705 G1























































































































































































































































Reviews:

No comments

Related manuals for EliteDesk 705 G1

Vecow RCS-9000 User Manual preview
RCS-9000
Brand: Vecow Pages: 172
Advantech ARK-3531 Series User Manual preview
ARK-3531 Series
Brand: Advantech Pages: 84
Moxa Technologies ThinkCore V481 User Manual preview
ThinkCore V481
Brand: Moxa Technologies Pages: 37
Wincomm WPC-766 User Manual preview
WPC-766
Brand: Wincomm Pages: 58
Aplex ACS-2170 User Manual preview
ACS-2170
Brand: Aplex Pages: 77
Asus B203 User Manual preview
B203
Brand: Asus Pages: 28
Asus Barebone System A7VT400 User Manual preview
Barebone System A7VT400
Brand: Asus Pages: 98
Asus Asteio D22 Quick Start Manual preview
Asteio D22
Brand: Asus Pages: 20
Asus B5081ZD User Manual preview
B5081ZD
Brand: Asus Pages: 44
Asus B204 User Manual preview
B204
Brand: Asus Pages: 104
Asus Barebone System T2-PH2 User Manual preview
Barebone System T2-PH2
Brand: Asus Pages: 114
Asus Asteio D20 User Manual preview
Asteio D20
Brand: Asus Pages: 252
HP RY883AA#ABA - Compaq Presario - SR5002HM Specifications preview
RY883AA#ABA - Compaq Presario - SR5002HM
Brand: HP Pages: 1
HP RY883AA#ABA - Compaq Presario - SR5002HM Quick Start preview
RY883AA#ABA - Compaq Presario - SR5002HM
Brand: HP Pages: 2
HP Envy Recline23 TouchSmart Beats SE All-in-One Disassembly Instructions preview
Envy Recline23 TouchSmart Beats SE All-in-One
Brand: HP Pages: 5
HP ENVY Phoenix 850 Disassembly Instructions Manual preview
ENVY Phoenix 850
Brand: HP Pages: 11
HP RN635AA#ABA Brochure preview
RN635AA#ABA
Brand: HP Pages: 2
HP Envy Phoenix 800 Disassembly Instructions Manual preview
Envy Phoenix 800
Brand: HP Pages: 11

Brands by name

Popular brands

Load more brands