manualshive.com logo in svg

HP Dv9233cl - Pavilion - Core 2 Duo 1.66 GHz, Maintenance And Service Manual

Share
Download
HP Dv9233cl - Pavilion - Core 2 Duo 1.66 GHz Maintenance And Service Manual Download Page 292

E–2

Maintenance and Service Guide

Power Cord Set Requirements

General Requirements

The requirements listed below are applicable to all countries and 
regions.

■

The length of the power cord set must be at least 1.5 m 
(5.0 ft) and a maximum of 2.0 m (6.5 ft).

■

All power cord sets must be approved by an acceptable 
accredited agency responsible for evaluation in the country or 
region where the power cord set will be used.

■

The power cord sets must have a minimum current capacity 
of 10 amps and a nominal voltage rating of 125 or 250 V AC, 
as required by each country’s or region’s power system.

■

The appliance coupler must meet the mechanical 
configuration of an EN 60 320/IEC 320 Standard Sheet C13 
connector for mating with the appliance inlet on the back of 
the computer.

Summary of Contents for Dv9233cl - Pavilion - Core 2 Duo 1.66 GHz
















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands