HP 8719ES Reference Manual Download Page 247 | Manualshive

Page: 247 / 283

background image

8-14

Preset State and Memory Allocation

Memory Allocation

NOTE

Even though calibration data is stored in non-volatile memory, if the
associated instrument state is not saved, you will not be able to retrieve the
calibration data after a power cycle.

The fixed memory is used to store the following data (you cannot change where this data is
stored and it does not affect your memory availability for storing user-allocated data):

• HP-IB addresses

• copy configuration (printer and plotter type, port, baud rate, handshake)

• power meter type (HP 436/437/438)

• display colors

• sequence titles

• sixth sequence

• power sensor calibration factors and loss tables

• user-defined calibration kits

• system Z0

• factory preset

• HP-IB configuration

• display intensity default

The maximum number of instrument states, calibrations, and memory traces that can
reside in non-volatile memory at any one time is limited to 31 instrument states, 128
calibrations (4 per instrument state, including the present instrument state), and 64
memory traces (4 per instrument state, including the present instrument state).

In addition, the number of instrument states and associated calibrations and memory
traces are limited by the available memory. To display the amount of unused memory on
the analyzer, press

. (Be sure you have selected

as

your disk type.) In the upper right-hand portion of the display, the value displayed as

Bytes free:

is the unused non-volatile memory. When you save to the internal memory,

you will see the number of bytes free decrease. When you delete files, the number of bytes
free increases. There is a maximum of 2 MBytes available.

If you have deleted registers since the last time the instrument was preset, the bytes
available for you to use may be less than the actual "bytes free" that is displayed. Deleting
registers to increase the available memory will work in cases where the registers being
deleted and the registers needing to be added are of the same standard size (such as
instrument states not having calibrations associated with them). In certain other cases,
however, you may have to press

after deleting registers so that the "bytes free"

value equals the available memory value. During a preset, the analyzer runs a memory
packer that de-fragments the free memory into one contiguous block.

Save/Recall

INTERNAL MEMORY

Preset

«
...
245
246
247
248
249
...
»

Summary of Contents for 8719ES




























































































































































































































































































Reviews:

No comments

Related manuals for 8719ES

Network Card-MS

Brand: Eaton Pages: 26

Brand: Vanguard Instruments Pages: 24

Brand: Kamstrup Pages: 100

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 12

Brand: Kamstrup Pages: 60

Brand: Kamstrup Pages: 136

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 155

Zetasizer Nano Series

Brand: Malvern Pages: 16

Ultraprobe 9000

Brand: UE Systems Pages: 25

ULTRAPROBE 10000

Brand: UE Systems Pages: 6

Brand: Sage Pages: 68

Brand: R&S Pages: 248

Brand: YOSensi Pages: 27

ENERGETIQ LDLS EQ-99X

Brand: Hamamatsu Pages: 45

Brand: Genie Pages: 14

Brand: Tektronix Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands