HP 300X - JetDirect Print Server Administrator'S Manual Download | Manualshive

Page: 89 / 102

background image

ENWW

TCP/IP Overview 89

Configuring IP Addresses

TCP/IP configuration parameters (such as IP address, subnet mask,
default gateway) can be configured on the HP Jetdirect print server
in a variety of ways. These values can be configured manually
through HP-supplied software, or they can be automatically
downloaded using DHCP or BOOTP each time the print server is
turned on.

Dynamic Host Configuration Protocol (DHCP)

DHCP allows a group of devices to use a set of IP addresses that are
maintained by a DHCP server. The device or host sends a request
to the server, and if an IP address is available, the server assigns
it to that device.

BOOTP

BOOTP is a bootstrap protocol used to download configuration
parameters and host information from a network server. BOOTP
uses UDP for its transport. In order for devices to boot and load
configuration information into RAM, they must communicate
through the bootstrap protocol BOOTP as a client with their server.

To configure the device, the client broadcasts a boot request packet
containing at least the hardware address of the device (HP Jetdirect
print server hardware address). The server answers with a boot
reply packet containing the information the device needs
to configure.

«
...
87
88
89
90
91
...
»

Summary of Contents for 300X - JetDirect Print Server







































































































Reviews:

No comments

Related manuals for 300X - JetDirect Print Server

Brand: ABLE Pages: 26

Brand: Canon Pages: 2

Brand: Canon Pages: 20

PIXMA TS9100 Series

Brand: Canon Pages: 100

Brand: Canon Pages: 100

Brand: Canon Pages: 105

Pixma G1010 Series

Brand: Canon Pages: 16

Brand: Canon Pages: 14

iP1500 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 21

Brand: Canon Pages: 68

iP4500 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 2

Pixma TS3400 Series

Brand: Canon Pages: 76

MAXIFY GX4000 Series

Brand: Canon Pages: 59

Aficio SP4100N-KP

Brand: Ricoh Pages: 4

Brand: Oce Pages: 340

T2150 SprintPro

Brand: Tally Pages: 124

Compa II Series

Brand: Valentin Pages: 110

V16 Automatic Shaker Unit

Brand: Garment Printer Ink Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands