HP 300X - JetDirect Print Server Administrator'S Manual Download | Manualshive

Page: 42 / 102

background image

42 Configuring for LPD Printing

ENWW

Note

The LPD functionality can be used with any host
implementation of LPD that complies with the
RFC 1179 document. The process for configuring
printer spoolers, however, may differ. See your
system documentation for information on
configuring these systems.

The LPD programs and protocol include the following:

Requirements for Configuring LPD

Before you can use LPD printing, your printer must be properly
connected to the network through the HP Jetdirect print server, and
you must have print server status information. This information is
listed on the HP Jetdirect printer configuration page. If you have
not printed a configuration page from your printer, see the
hardware installation guide for your print server or your printer’s
getting started guide for instructions. You must also have the
following:

●

An operating system that supports LPD printing.

●

Superuser (root) or Administrator access to your system.

Table 4.1

LPD Programs and Protocols

Program Name

Purpose of Program

lpr

Queues jobs for printing

lpq

Displays print queues

lprm

Removes jobs from print queues

lpc

Controls print queues

lpd

Scans and prints the files if the specified
printer is connected to the system.

If the specified printer is connected to another
system, this process forwards the files to an
lpd process on the remote system where the
files are to be printed.

«
...
40
41
42
43
44
...
»

Summary of Contents for 300X - JetDirect Print Server







































































































Reviews:

No comments

Related manuals for 300X - JetDirect Print Server

Brand: NCR Pages: 5

2006NPC - DocuColor Color Laser

Brand: Xerox Pages: 4

Brand: Star Pages: 82

Brand: Konica Minolta Pages: 15

Brand: Xerox Pages: 214

Brand: Cardco Pages: 28

Brand: Microcom Pages: 73

Brand: Citizen Pages: 57

SUPERO SuperServer 6026TT-H6IBQRF

Brand: Supero Pages: 110

Brand: NetMedia Pages: 2

Brand: Advantech Pages: 96

Brand: Airlink101 Pages: 36

Brand: Boley Pages: 20

Brand: L-Mark Pages: 62

xSeries 342 2RX

Brand: IBM Pages: 158

Palcare PAL-211401

Brand: PalatiumCare Pages: 64

Brand: 3D Systems Pages: 72

PRIMERGY RX2520 M4

Brand: Fujitsu Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands