manualshive.com logo in svg

horsch Terrano 4.3 GX, Operating Instructions Manual

Share
Download
horsch Terrano 4.3 GX Operating Instructions Manual Download Page 42

6 | Assembly groups

42

60084498 • 01 • 06/2022 • en

NOTE

The stone release protection serves as protection system against obstacles in the
field.

Ø

Reduce the working depth if the stone release protection is often triggered
under hard ground conditions, even without stones as obstacles.

6.2 MulchMix coulter

WARNING

Danger of injury caused by machine lowering

Ø

Always support the machine with suitable means before starting any assembly
or maintenance work on tines and coulters.

Ø

Secure the lift cylinders with aluminium clips.

The tines can be equipped with different coulters to suit various operating condi-
tions.

1

2

3

4

4

1

Tine stem

2

Coulter tip

3

Guide plate

4

Lateral wings

Different variants are available for the components:

• coulter tip - narrow, carbide-tipped (HM)

• Guide plate - narrow, wide

• lateral wings - narrow, carbide-tipped (HM)

Summary of Contents for Terrano 4.3 GX



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands