Honeywell HERMetic UTImeter Gtex Chem IIC Operation And Service Manual Download Page 39

Page: 39 / 83

50489/GTEX Chem IIC/1805

UTImeter Gtex Chem IIC

9.1.2. During gauging

When the unit is already switched on and working, it is always possible to see what power is left with the

battery by entering the settings menu:

Press on "+" to enter the settings menu,

Press on "enter", "LED menu" is displayed,

Press on "+"; "T. unit" is displayed,

Press on "+", "Resol." is displayed,

Press on "+", "Language" is displayed,

Press on "+", "Battery" is displayed,

Press on "enter",

The remaining battery power is displayed in percentage and as a bar-graph; pressing "+" again allows to

see the tension of the battery (B); the last information (A) is internal.

Press "-" two times to come back in measurement mode.

UTImeter

Battery

Init.

*********

25.94°C

Settings

T. unit

Resol.

Language

Ver x.xx

LED menu

Battery

éé

B 7.62 V

A 3.22 V

éé

47%

Figure 10-3

Summary of Contents for HERMetic UTImeter Gtex Chem IIC




















































































Search results

Summary of Contents for HERMetic UTImeter Gtex Chem IIC

Reviews:

Honeywell HERMetic UTImeter Gtex Chem IIC, Operation And Service Manual, Page: 39 / 83

Search results

Summary of Contents for HERMetic UTImeter Gtex Chem IIC

Reviews: