Honeywell HERMetic UTImeter Gtex Chem IIC Operation And Service Manual Download Page 19

Page: 19 / 83

50489/GTEX Chem IIC/1805

UTImeter Gtex Chem IIC

6.4. Tape protection

The tape protection tube is a mechanical safety

device which prevents the valve from being closed

as long as the sensing probe is inside the tank.

When the sensing probe is lowered the protection

tube will follow the sensing probe by gravity until

the tube is retained by a ring located inside the

coupler. In that position the protection tube

prevents closing the valve. When the tape is

wound up the protection tube will stay in position

until it is pushed up by the sensing probe. Before

instrument is used check that the protection tube

is moving freely. For cleaning purposes the

protection tube is slotted.

VALVE CLOSED

VALVE OPEN

TAPE PROTECTION TUBE

STORAGE TUBE

SENSOR

RETAINER

QUICK CONNECT

COUPLER

BALL VALVE

Figure 7-8

Summary of Contents for HERMetic UTImeter Gtex Chem IIC




















































































Search results

Summary of Contents for HERMetic UTImeter Gtex Chem IIC

Reviews:

Honeywell HERMetic UTImeter Gtex Chem IIC, Operation And Service Manual, Page: 19 / 83

Search results

Summary of Contents for HERMetic UTImeter Gtex Chem IIC

Reviews: