Home
/
Honeywell
/
Centraline FALCON
/
User Manual

Honeywell Centraline FALCON, User Manual, Page: 194 / 276

Share

Page: 194 / 276

Honeywell Centraline FALCON User Manual Download Page 194

FALCON

USER GUIDE

EN2Z-0962GE51 R0715

190

•

EOH/EOV Optimization

(applies to AV, BV, and MV datapoints)

Check whether the datapoint should be optimized (Yes) or not (No), in case
the datapoint is used as setpoint for energy optimized heating or ventilation.

•

Reset To

(applies to PC, BI and BO datapoints only)

Here you can reset the current value to a specific value. The counting will
restart.

•

Time of Last Reset

(applies to PC, BI and BO datapoints only)

Shows the time of the last reset.

Status

(All datapoint types)

Here the status flag condition and the event state are displayed.

If checked, the status flags have the following meaning:

•

In Alarm

Datapoint is in alarm. Cause can be faults, Off-normal conditions, and life-
safety alarm.

•

Fault

The datapoint or the physical input is not reliable, e.g. in case of sensor
break (Open Loop).

•

Overridden

Datapoint is in manual operation mode. Value has been overwritten.

•

Out of Service

Physical input is decoupled from the datapoint, e.g. in case of manual
override. The present value displayed is not the present value, which would
be delivered by the physical input.

NOTE: Multiple flag indications are possible.

Example:

A ´To-Fault transition` causes also always an alarm. Hence both, the ´In Alarm`

and the ´Fault` status flags are enabled.

•

Event State (All datapoint types)

Shows the event state of the datapoint:

«
...
192
193
194
195
196
...
»

Summary of Contents for Centraline FALCON





















































































































































































































































































Reviews:

No comments