Honda BF200D Manual Download Page 104

Page: 104 / 152

104

OPERATION

3. If the overheat warning system

stays activated, stop the engine.

Tilt up the outboard motor and

check the water intakes for

obstructions. If there are no

obstructions at the water intakes,

return to the closest boat landing

and contact your closest authorized

Honda outboard motor dealer.

When the PGM-FI activated:

1. Consult with an authorized Honda

outboard motor dealer.

When the ACG warning system is

activated.

1. Check the battery (see page 129). If

the battery is OK, consult with an

authorized Honda outboard motor

dealer.

When the water separator buzzer

sounds:

1. Check the water separator for water

contamination. If water is

accumulated, drain them (see page

126).

COOLING WATER INTAKE PORT

(each side)

WATER SEPARATOR

42ZVL600.book 104 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands