Honda BF200D Manual Download Page 41

Page: 41 / 152

CONTROLS AND FEATURES

Tilt Lock Lever

Use the tilt lock lever to raise the

outboard motor and lock it in the

position when the boat is moored or

anchored for a long time.

Tilt the outboard motor as far as it

goes and move the lock lever in the

locking direction.

Trim Tab

If the steering wheel/handle is pulled

to the side while running at full

speed, adjust the trim tab so that the

boat runs straight ahead.

Loosen the tightening bolt and turn

the trim tab right or left to adjust.

Anode

The anode is a sacrificial material

which helps to protect the outboard

motor from corrosion.

Do not paint the anode. It

deteriorates the function of the

anode, which can lead to rust and

corrosion damage to the outboard

motor.

TILT LOCK LEVER

LOCK

FREE

TIGHTENING

BOLT

TRIM TAB

ANODE

(each side)

ANODE

(stern bracket)

42ZVL600.book 41 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands