Honda BF200D Manual Download Page 120

Page: 120 / 152

120

MAINTENANCE

Spark Plugs

To ensure proper engine operation,

the spark plug must be properly

gapped and free of deposits.

Check-clean/Replace interval:

Every 100 operating hours or 6

months.

Recommended spark plug:

ZFR6K-11E (NGK)

Use only the recommended spark

plugs or equivalent. Spark plugs

which have an improper heat range

may cause engine damage.

1. Disconnect the battery negative (

–

)

terminal.

2. Unlock and remove the engine

cover (see page 57).

CAUTION

The spark plug becomes very hot

during operation and will remain

hot for a while after stopping the

engine. Allow the engine to cool

before servicing the spark plug.

42ZVL600.book 120 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands