Honda BF200D Manual Download

Page: 57 / 152

6. PRE-OPERATION CHECKS

BF200D/BF225D/BF250D is 4-stroke,

water cooled outboard motor which

uses unleaded regular gasoline for fuel.

It also requires the engine oil. Check

the following before operating the

outboard motor.

Before each use, look around and

underneath the engine for signs of oil

or gasoline leaks.

Engine Cover Removal/Installation

1. Pull all the engine cover latches.

2. Remove the engine cover by taking

it up.

<Installation>

1. Place the engine cover on the main

body.

2. Slide the engine cover so that the

cover lock on the cover is mated

with the lock in the main body.

CAUTION

Perform the following

pre-operation checks with the

engine stopped.

Front

ENGINE COVER LATCH

Side

ENGINE COVER LATCH (each side)

MAIN BODY SIDE

COVER SIDE

COVER LOCKS

Side

42ZVL600.book 57 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands