Honda BF200D Manual Download Page 51

Page: 51 / 152

INSTALLATION

Connect the battery cables:

1. Connect the cable with the red

terminal cover to the positive (+)

terminal of the battery.

2. Connect the cable with the black

terminal cover to the negative (–)

terminal of the battery.

When more than one outboard motor

is mounted on a boat, connect a

battery to each respective outboard

motors.

• Be sure to connect the (+) side

battery cable first. When

disconnecting the cables,

disconnect the (

–

) side first then

the (+) side.

• Unless the cables are properly

connected to the terminals, the

starter motor may fail to operate

normally.

• Be careful to avoid connecting

the battery in reverse polarity, as

this will damage the

battery-charging system in the

outboard motor.

• Do not disconnect the battery

cables while the engine is

running. Disconnecting the

cables while the engine is

running, will damage the

outboard motor’s electrical

system.

• Do not place the fuel tank near

the battery.

(–) TERMINAL

(+) TERMINAL

RED

BLACK

42ZVL600.book 51 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands