Honda BF200D Manual Download Page 20

Page: 20 / 152

CONTROLS AND FEATURES

Shifting gear into forward, reverse, or

neutral and the engine speed

adjustment can be performed with the

remote control lever.

FORWARD:

Moving the lever to the FORWARD

position (i.e. approximately 20° from

the NEUTRAL position) engages the

gear into forward. Moving the lever

further from the FORWARD position

will increase the throttle opening and

the boat forward speed.

NEUTRAL:

Engine power is cut off from the

propeller.

REVERSE:

Moving the lever to the REVERSE

position (i.e. approximately 20° from

the NEUTRAL position) engages the

gear into reverse. Moving the lever

further from the REVERSE position

will increase the throttle opening and

the boat reverse speed.

Remote Control Lever (D2 type)

SINGLE TYPE

REMOTE CONTROL

LEVER

FORWARD

NEUTRAL

REVERSE

REMOTE CONTROL LEVERS

DUAL TYPE

MAXIMUM

REMOTE CONTROL LEVER

MAXIMUM

REVERSE

NEUTRAL

FORWARD 20°

20°

THROTTLE

OPENING

MINIMUM

THROTTLE

OPENING

FORWARD

NEUTRAL

REVERSE

42ZVL600.book 20 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands