Honda BF200D Manual Download Page 111

Page: 111 / 152

111

10. TRANSPORTING

Fuel Line Disconnection

Before transporting the outboard

motor, disconnect and remove the

fuel line.

Transporting

When transporting the outboard

motor on a vehicle, perform the

following.

1. Remove the engine cover (see page

57).

2. Set the hoist hooks against the

lifting eyes and hang the outboard

motor to remove it from the boat.

WARNING

Gasoline is extremely

flammable, and gasoline vapor

can explode, causing serious

injury or death.

• Be careful not to spill fuel.

Spilled fuel or fuel vapor may

ignite. If any fuel is spilled,

make sure the area is dry

before storing or transporting

the outboard motor.

• Do not smoke or allow flames

or sparks where fuel is drained

or stored.

LIFTING EYES

HOIST HOOKS

42ZVL600.book 111 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands