Honda BF200D Manual Download Page 27

Page: 27 / 152

CONTROLS AND FEATURES

FUNCTION SWITCHES

(D1 type)

Function switches are used for

operations in the fast idle mode and

trolling mode.

<Fast Idle Mode>

The fast idle mode is only needed for

starting carbureted outboard models.

The BF200D, BF225D and BF250D

models use programmed fuel

injection so, this mode will not be

needed for starting.

After the engine starts and if the

outside temperature is below

5°C (41°F), the fast idle mode can be

used to accelerate engine warm up.

Use the [-] switch and the remote

control lever to adjust the engine

speed without gearshift when

warming up the engine.

Keeping the [-] switch pressed when

the remote control lever is in the

NEUTRAL position, turn the lever

forward. Keep turning the lever

forward. The throttle opens and the

engine speed increases after the lever

passed the shift point.

Note that the gearshift mechanism

does not function when the [-] switch

is pushed once and then released after

the remote control lever is moved.

The control lever does not operate

unless the neutral release lever is

pulled.

[-] SWITCH

[+] SWITCH

752//

)$67,'/(

752//

:$50

$&7

NEUTRAL

FORWARD

REVERSE

REMOTE

CONTROL

LEVER

NEUTRAL

RELEASE

LEVER

Pull up

42ZVL600.book 27 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands