Honda BF200D Manual Download Page 100

Page: 100 / 152

100

OPERATION

If the engine oil pressure drops and/

or the engine overheats, either or both

warning systems could be activated.

When activated the engine speed will

decrease gradually and the green oil

pressure indicator will turn OFF and

the red overheat indicator will turn

ON. A continuous buzzer will sound

on all type.

The engine speed can not be

increased with a larger throttle

opening until the malfunction is

corrected.

When the malfunction is corrected

the engine speed will increase

gradually.

If the engine overheats, the engine

will stop in 20 seconds after the

engine protection system will limit

engine speed.

Each warning system of PGM-FI,

ACG, oil pressure, overheat, and

water separator is activated as

described in the following table.

OIL PRESSURE

INDICATOR

(GREEN)

ACG

INDICATOR

(RED)

OVERHEAT

INDICATOR

(RED)

BUZZER

(R1 type)

PGM-FI

INDICATOR

(RED)

BUZZER

OVERHEAT

INDICATOR

(RED)

OIL PRESSURE

INDICATOR

(GREEN)

(R2, R3 type)

PGM-FI

INDICATOR

(RED)

ACG

INDICATOR

(RED)

PGM-FI

INDICATOR

(RED)

OIL PRESSURE

INDICATOR

(RED)

ACG

INDICATOR

(RED)

(Display Assy type)

OVERHEAT

INDICATOR

(RED)

Engine Protection System

<Engine Oil Pressure, Overheat,

Water Separator, PGM-FI and

ACG Warning Systems>

42ZVL600.book 100 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands