background image

129

MAINTENANCE

Battery

Battery handling differs according 

to the type of the battery and the 

instructions described below might 

not be applicable to the battery of 

your outboard. Refer to the battery 

manufacturer’s instructions.

 <Battery Fluid Level>

Check whether the battery fluid is 

between the upper and lower levels, 

and check the vent hole in the battery 

caps for clogging.

If the battery fluid is near or below 

the lower level, add the distilled 

water to the upper level.

WARNING

Batteries produce explosive  

gases: If ignited, an explosion can 

cause serious injury or blindness. 

Provide adequate ventilation 

when charging.

• CHEMICAL HAZARD: 

Battery electrolyte contains 

sulfuric acid. Contact with eyes 

or skin, even through clothing, 

may cause severe burns. Wear 

a faceshield and protective 

clothing.

• Keep flames and sparks away, 

and do not smoke in the area. 

ANTIDOTE: If electrolyte gets 

into your eyes, flush 

thoroughly with warm water 

for at least 15 minutes and call 

a physician immediately.

• POISON: Electrolyte is poison.

ANTIDOTE:

External: Flush thoroughly 

with water.

Internal: Drink large 

quantities of water or milk. 

Follow with milk of 

magnesia or vegetable oil, 

and call a physician 

immediately.

• KEEP OUT OF REACH OF 

CHILDREN.

UPPER LEVEL

LOWER LEVEL

BATTERY 

CAP

42ZVL600.book  129 ページ  2018年7月19日 木曜日 午前9時6分

Summary of Contents for BF200D

























































































































































Reviews: