![HEIDENHAIN TNC 426 CB Technical Manual Download Page 798](http://html1.mh-extra.com/html/heidenhain/tnc-426-cb/tnc-426-cb_technical-manual_2118721798.webp)
6 – 468
HEIDENHAIN Technical Manual TNC 426, TNC 430
For the commissioning of new machines, HEIDENHAIN recommends
adjusting the PWM frequency to fit axis modules (normally 4 kHz, see
SIEMENS documentation). If the power module of the spindle gets too warm
in spite of a reduction of the PWM frequency from 5 kHz to 4 kHz, then the
reference value for the I
2
t monitoring (MP2303) or the rated current I
N
must
be reduced.
Reduction of the reference value for the I
2
t monitoring or the rated
current I
N
The reduction of the rated current I
N
of the power modules, as well as the
datum value for I
2
t monitoring can be calculated from two values (X1, X2) that
are given in the SIEMENS documentation.
The percent reduction of the rated current can be calculated with the following
formula:
n
X1 = Reduction factor of the current in % at a PWM frequency of 8 kHz
n
X2 = PWM threshold frequency in kHz at which the electrical power
reduction begins
n
f
PWM
= PWM frequency in kHz set in MP2180.0-8
This results in the reference value for I
2
t monitoring:
Example for a 50-A power module:
n
Axis power module with 50 A, PWM frequency of 5 kHz, X1 = 40 %, X2 =
4 kHz
n
Spindle power module with 50 A, PWM frequency of 5 kHz, X1 = 40 %, X2
= 3.2 kHz
Note
A reduction of the PWM frequency has no effect on the maximum speed,
but it means that the axis and the spindle without integral DSP must be
commissioned again.
X
R
[%]
100
100
X1
–
(
)
8 kHz
f
PWM
–
(
)
⋅
8 kHz
X2
–
--------------------------------------------------------------------------------------------
X1
+
è
ø
æ
ö
–
=
X
B
1
X
R
[%]
100
--------------------
–
=
X
R
[%]
100
100
40
–
(
)
8 kHz
5 kHz
–
(
)
⋅
8 kHz
4 kHz
–
----------------------------------------------------------------------------------------
40
+
è
ø
æ
ö
–
15 %
=
=
X
B
1
15
100
-----------
–
0 85
,
=
=
X
R
[%]
100
100
40
–
(
)
8 kHz
5 kHz
–
(
)
⋅
8 kHz
3,2 kHz
–
----------------------------------------------------------------------------------------
40
+
è
ø
æ
ö
–
22,5 %
=
=
X
B
1
22,5
100
-------------
–
0.78
=
=
Summary of Contents for TNC 426 CB
