
December 2001
Spindle
6 – 187
Disable speed
output for spindle
With M4008 you can block the speed output for the spindle. At the same time,
M03, M04 or M05 are highlighted. The nominal speed value is zero.
Gear ranges
You can define up to eight gear ranges:
7
7
7
7
In MP3510.x, enter for each gear range the rated speed for S-override
100%.
Enter the value zero for unnecessary gear ranges.
7
7
7
7
In MP3210.x, enter for every gear range the S analog voltage or motor
revolutions at rated speed.
7
7
7
7
In MP3240.1, define the minimum nominal speed value for the motor.
7
7
7
7
In MP3120, define whether zero is permitted as a programmed speed.
If an impermissible speed is programmed, M4004 is set and the error
message
WRONG RPM
is displayed.
MP3510.0-7 Rated speed for the gear ranges 1 to 8
Input:
0 to 99 999.999 [rpm]
MP3210.0-7 Analog nominal spindle voltage at rated speed for the gear
ranges 1 to 8
Input:
0 to 100.000 [V]
MP3210.0-7 Digital spindle motor revolutions at rated speed for the
gear ranges 1 to 8
Input:
0 to 100.000 [1000 rpm]
MP3240.1
Analog spindle: Minimum nominal value voltage
Input:
0 to 9.999 [V]
MP3240.1
Digital spindle: Minimum motor speed
Input:
0 to 9.999 [1000 rpm]
MP3120
Zero speed permitted
Input:
0: S = 0 permitted
1: S = 0 not allowed
Set
Reset
M4008
Disable speed output for spindle
PLC
PLC
Note
The gear range from W256 is output when the spindle speed is 0.
Set
Reset
M4004
Impermissible speed was
programmed
NC
NC
Summary of Contents for TNC 426 CB
