HandEra 330 User Manual Download

Page: 14 / 248

1-4

HandEra 330 User Guide

Installing Batteries

This section discusses how to install alkaline batteries.

Press the latch on the battery door and lift the battery door away
from your HandEra handheld. Refer to Figure 1-3.

Install four AAA alkaline batteries into the battery compartment
with the correct polarity. Figure 1-3 shows correct polarity for
the batteries.

Note:

You may need to perform a soft reset when installing

batteries for the first time.

Insert the battery door back into place flush with the back of
your HandEra computer and click the door into position.

Figure 1-3. Battery Installation

Push Tab Left to
Open Battery
Door

Summary of Contents for 330

























































































































































































































































Search results

Summary of Contents for 330

Reviews:

Related manuals for 330

Brands by name

Popular brands

HandEra 330, User Manual

Search results

Summary of Contents for 330

Reviews:

Related manuals for 330

Brands by name

Popular brands