HamGadgets MasterKeyer MK-1 User Manual Download Page 33 | Manualshive

Page: 33 / 50

background image

Firmware Version 1.21

2/2/2010

32

Repeat Word: The /R command will repeat the last word sent, including the space after it
(if any).

Speed Control: The

/Sx

commands can be used to control the sending speed during a

message. Bear in mind that each of these commands is in effect only until the message
terminates, when settings are returned to normal.

•

/Snn

sets the speed to nn WPM, where nn can be anything from 5 to 99.

•

/SU

increases sending speed by one word per minute.

•

/SD

decreases sending speed by one word per minute.

•

/SH

is used to control HSCW mode. When followed by a number, it will set the

HSCW mode speed to that number of letters per minute (LPM) times 100. For
example, to set a HSCW speed of 6000 letters per minute, you would use /SH60.
/SH by itself will cancel HSCW mode.

•

/SQ

will control QRSS mode. When followed by a number from 1 to 120, the dot

length is set to n seconds. /SQ by itself will cancel QRSS mode.

•

/SR

will reset any speed changes immediately.

•

/S0

will reset speed changes, the same as

/SR

.

All speed changes are canceled at the end of the memory message.

MYCALL: The

/Y

command will send the contents of the MYCALL setting, if there is

one. If the MYCALL setting is empty, this command has no effect.
Example:

CQ CQ CQ DE /Y /Y /Y K

Memory Calling & Chaining: A memory message can “call” any other message.  When
a slant bar followed by a single digit is encountered, the corresponding message from the
active memory bank is called.  If the slant bar is followed by two digits, it is interpreted
as a bank and message number.

Control is passed to the “called” message, then returns when that message is complete.
Messages can be called up to eight deep.

Examples:

•

/2

calls Message 2 from the current message bank

•

/32

calls message 2 from bank 3

Computer Commands

Commands may be sent from the computer via the USB interface whenever the keyer is
not in keyboard Morse mode – this means when buttons 3 & 6 are not illuminated.
Commands can be sent either by a program, or manually using a serial terminal program
such as HyperTerminal, PuTTY or Minicom.  Characters received while in normal
operating mode will be queued until a carriage return (ASCII 13, hex 0x0D, the Enter key
on your keyboard) is sent.  The command will be acted upon as soon as any pending
messages or paddle activity is finished.

«
...
31
32
33
34
35
...
»

Summary of Contents for MasterKeyer MK-1



















































Reviews:

No comments

Related manuals for MasterKeyer MK-1

Brand: Uebo Pages: 4

Brand: Digitrax Pages: 8

Brand: Magnimage Pages: 40

Brand: Teac Pages: 116

Brand: YASKAWA Pages: 120

Brand: M-system Pages: 5

Brand: Volt Polska Pages: 5

Brand: Black Box Pages: 20

Y/C to NTSC Conversion PCN-40

Brand: Link Pages: 2

Brand: Wirez Pages: 16

Brand: AVT Pages: 82

GlobeTrotter Ex GE 0003

Brand: Option Audio Pages: 4

Brand: Teac Pages: 18

Brand: Digitus Pages: 4

Brand: Goobay Pages: 4

Brand: Hoymiles Pages: 2

Brand: Microchip Technology Pages: 24

Brand: OLIJU Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands