GW Instek LCR-8000G Series User Manual Download Page 24

Page: 24 / 144

LCR-8000G Series User Manual

Fixture Connection

Fixture structure

Background

The standard fixture is a four-wire type with a
common terminal for screen connection. The outer
terminals (Hforce and Lforce) provide the current
and the inner terminals (Hsense and Lsense)
measures the potential.

Diagram

FORCE

SENSE

FORCE

–

GND

(Optional)

Description

HFORCE

Carries the signal current source.
Connected to the + side of the device
under test.

HSENSE

Together with Lsense, monitors the
Potential. Connected to the + side of
the device under test.

LSENSE

Together with Hsense, monitors the
Potential. Connected to the – side of
the device under test.

LFORCE

Accepts the signal current return.
Connected to the – side of the device
under test.

GND

If the test component has a large
metal area NOT connected to either
of the terminals, connect the GND
clip to minimize noise level.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LCR-8000G Series

















































































































































Search results

Summary of Contents for LCR-8000G Series

Reviews:

Related manuals for LCR-8000G Series

Brands by name

Popular brands

GW Instek LCR-8000G Series, User Manual

Search results

Summary of Contents for LCR-8000G Series

Reviews:

Related manuals for LCR-8000G Series

Brands by name

Popular brands