GW Instek LCR-8000G Series User Manual Download Page 56 | Manualshive

Page: 56 / 144

background image

LCR-8000G Series User Manual

56

Running Measurement

Select Single measurement

Background

The data capture can be manually controlled
(Single) or automatically updated (Repetitive).
In single measurement, the measurement is
activated by pressing the Trigger key.
In repetitive measurement, the measurement is
automatically done and the display is updated
according to the speed (timing) setting.

Panel operation

1.

Press the Sing/Rep key repeatedly
until the “Single Shot Mode”
message appears on the display.

Sing/Rep

Single Shot Mode

2.

The measurement update indicator (*) does not
appears at the top left corner of the display.

MEASUREMENT MODE

nS

D

7

3.

To capture measurement data, press
the Trigger key. The measurement
update indicator (*) blinks and the
measurement result is updated on
the display.



MEASUREMENT MODE

0.01234

0.2179

nS

D

*7

–

www.

.com

[email protected]

1.800.561.8187

«
...
54
55
56
57
58
...
»

Summary of Contents for LCR-8000G Series

















































































































































Reviews:

No comments

Related manuals for LCR-8000G Series

Brand: Kane Pages: 4

SMatrix DMX2400

Brand: dallmeier Pages: 12

Brand: Chroma Pages: 63

Ranger TDR VDV501-090

Brand: Klein Tools Pages: 44

Brand: PRONIVO Pages: 40

Brand: socomec Pages: 34

Brand: Dynojet Pages: 88

Brand: VP instruments Pages: 15

Brand: Cal Test Electronics Pages: 12

Brand: kruss Pages: 115

Brand: PCB Piezotronics Pages: 11

Brand: Dakota Digital Pages: 38

Brand: Swema Pages: 4

Panametrics XDP

Brand: Baker Hughes Pages: 64

Brand: IROX Pages: 8

Brand: Magneti Marelli Pages: 20

KLIMA GUARD 30.5010

Brand: TFA Pages: 22

Brand: Zico Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands